Absolutely, sound like an almost exact copy of my own setup; got 16x SainSmart, 8x USB too, Teensy, VP, FP, Mame, Windows10, PinballX. The UIO is such a beautiful piece of well behaved hardware!
You'll need a DirectOutputFramework\config\Cabinet.xml, something like this if you haven't one running already (may not match, it's just an example):
<?xml version="1.0"?>
<Cabinet xmlns:xsi="http://www.w3.org/20...Schema-instance" xmlns:xsd="http://www.w3.org/2001/XMLSchema">
<Name>Gianna</Name>
<!-- no need to have pacio in, will be autodetected -->
<!-- no need to have ft245rbitbangcontroller in, will be autodetected -->
<!-- no need to have pacled64 in, should be autodetected -->
<!-- no need to have pacdrive in, should be autodetected -->
<!-- no need to have ledwiz in, should be autodetected -->
<!-- philips hue bridge will autoconfig but still needs to be manually added for ip and key, while channels / setup will rely in dof configtool -->
<OutputControllers>
<TeensyStripController>
<Name>TeensyStripController</Name>
<NumberOfLedsStrip1>576</NumberOfLedsStrip1>
<NumberOfLedsStrip2>144</NumberOfLedsStrip2>
<NumberOfLedsStrip3>144</NumberOfLedsStrip3>
<NumberOfLedsStrip4>0</NumberOfLedsStrip4>
<NumberOfLedsStrip5>0</NumberOfLedsStrip5>
<NumberOfLedsStrip6>0</NumberOfLedsStrip6>
<NumberOfLedsStrip7>0</NumberOfLedsStrip7>
<NumberOfLedsStrip8>0</NumberOfLedsStrip8>
<ComPortName>COM5</ComPortName>
</TeensyStripController>
</OutputControllers>
<Toys>
<LedStrip>
<Name>PF Back Flashers MX</Name>
<Width>72</Width>
<Height>8</Height>
<LedStripArrangement>LeftRightAlternateTopDown</LedStripArrangement>
<ColorOrder>GRB</ColorOrder>
<FirstLedNumber>1</FirstLedNumber>
<FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
<OutputControllerName>TeensyStripController</OutputControllerName>
</LedStrip>
<LedStrip>
<Name>PF Left Flashers MX</Name>
<Width>1</Width>
<Height>144</Height>
<LedStripArrangement>TopDownLeftRight</LedStripArrangement>
<ColorOrder>GRB</ColorOrder>
<FirstLedNumber>577</FirstLedNumber>
<FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
<OutputControllerName>TeensyStripController</OutputControllerName>
</LedStrip>
<LedStrip>
<Name>PF Right Flashers MX</Name>
<Width>1</Width>
<Height>144</Height>
<LedStripArrangement>TopDownLeftRight</LedStripArrangement>
<ColorOrder>GRB</ColorOrder>
<FirstLedNumber>721</FirstLedNumber>
<FadingCurveName>SwissLizardsLedCurve</FadingCurveName>
<OutputControllerName>TeensyStripController</OutputControllerName>
</LedStrip>
<LedWizEquivalent>
<Name>LedWizEquivalent 30</Name>
<Outputs>
<LedWizEquivalentOutput>
<OutputName>PF Back Flashers MX</OutputName>
<Description>outputnumbers match configtool</Description>
<LedWizEquivalentOutputNumber>1</LedWizEquivalentOutputNumber>
</LedWizEquivalentOutput>
<LedWizEquivalentOutput>
<OutputName>PF Left Flashers MX</OutputName>
<LedWizEquivalentOutputNumber>4</LedWizEquivalentOutputNumber>
</LedWizEquivalentOutput>
<LedWizEquivalentOutput>
<OutputName>PF Right Flashers MX</OutputName>
<LedWizEquivalentOutputNumber>7</LedWizEquivalentOutputNumber>
</LedWizEquivalentOutput>
</Outputs>
<LedWizNumber>30</LedWizNumber>
</LedWizEquivalent>
</Toys>
<Colors/>
<Curves/>
<AutoConfigEnabled>true</AutoConfigEnabled>
</Cabinet>
You'll want to have DOF R3, the official version, installed first. Then you just overwrite that installation set of files with say the latest build on https://github.com/r...ctOutput/Builds, like the bottom _20170606 a day ago. Then, hop over to configtool on that other site, create an account, "My Account", set WS2811=1, Ultimate/IO=1, SainSmart=1 if you've got the 8-port USB version hooked up. "Save settings".
Next go to Port Assignments. There's a "Device" drop down list. The active device is showing a lot of ports below, 96 for the "Ultimate/IO 1" for instance. Point being 3 ports for R(1), G(2) and B(3) if you have them. Match your ports to your solder / physical UIO header output connectors. Initially I just mapped Flipper Left to port 1 and Flipper Right to port 3, which happened to be an RGB joystick. Then pressed "Save Config", then "Generate Config", and put all the INI files inside your DirectOutputFramework\config directory.
If that worked, I'd get red and blue flashing when using the left and right flippers in Attack from Mars VP9x-version. Very easy test. If you get that far, you're almost done. DOF is now actually running.
In the DOF-directory there's a "DirectOutputConfigTester". You can run this, select your DirectOutputFramework\config\GlobalConfig_B2SServer.xml, a table file (like Visual Pinball\Tables\Attack from Marsvp91x.vpt), and then a RomName (like afm). You then press OK, and can then manually toggle outputs. Quit, then check your DirectOutput.log for issues. It should show you that the UIO was detected at the top. There's also (for me anyway) a similar DirectOutput.log inside your VP\Tables directory which will be used for VP.
Something like this:
---------------------------------------------------------------------------------
2017.06.06 20.45.27.188 DirectOutput Logger initialized.
2017.06.06 20.45.27.188 DirectOutput Version 0.9.6366.37353 as of 2017.06.06 20.45
2017.06.06 20.45.27.188 UltimateIO edition. Original project at https://github.com/DirectOutput/DirectOutput
2017.06.06 20.45.27.188 Hail to the lizardking!
2017.06.06 20.45.27.188 Global config loaded from: D:\Tools\DirectOutput\DirectOutputFramework\config\GlobalConfig_B2SServer.xml
2017.06.06 20.45.27.188 Loading Pinball parts
2017.06.06 20.45.27.188 Loading cabinet
2017.06.06 20.45.27.188 Will load cabinet config file: D:\Tools\DirectOutput\DirectOutputFramework\config\Cabinet.xml
2017.06.06 20.45.27.766 2 output controller defnitions and 4 toy definitions loaded from cabinet config.
2017.06.06 20.45.27.766 Cabinet config file has AutoConfig feature enabled. Calling AutoConfig.
2017.06.06 20.45.27.782 Cabinet auto configuration started
2017.06.06 20.45.27.797 PacDriveSingleton.PacUIOGetIdList: i=0, numdevices=1, DeviceType=IPACIO
2017.06.06 20.45.27.797 PacUIOAutoConfigurator.AutoConfig.. Detected I-PAC Ultimate[0], name=PacUIO 0
2017.06.06 20.45.27.797 Detected and added PacUIO Id 0 with name PacUIO 0
2017.06.06 20.45.27.797 Added LedwizEquivalent Nr. 27 with name PacUIO 0 Equivalent 1 for PacUIO with Id 0
Once you get all your stuff working, there's day&night modes, custom output overrides etc you can do. Then RGB-stuff with the LED-strips is a whole different thing. Wear sunglasses, even better; cover up the stuff while testing. When everything goes to ...not well, you hit the sack and try again another time 
And hey, if you've got Philips Hue; a few days ago I hooked up about 16 bulbs and LED-strips to DOF and enjoyed some Attack from Mars. It works. And it's quite insane. It's got lag, but it's cool. Then you exit a table, and you're in complete darkness C-8
AND: I almost forgot. If you haven't already, update your UIO-board using the Ultimarc firmware updater at https://www.ultimarc.com/download.html
Mine was a bit old, and I think it partially solved an issue I was having. Worth checking out.
Edited by rambo3, 07 June 2017 - 08:48 PM.