Jump to content



Photo
* * * * * 2 votes

usb dot matrix driver board - who wants one?


  • Please log in to reply
1473 replies to this topic

#1321 settingsons

settingsons

    Pinball Fan

  • VIP
  • 959 posts
  • Location:Switzerland

  • Flag: Switzerland

  • Favorite Pinball: Terminator 2 and many EM machines



Posted 07 July 2012 - 07:51 PM

Thanks for that Russ. I flashed the firmware and can't see any issues. Working great so far smile.gif

I was playing with the dmdlogo.txt and for some reason couldn't get it to work. On boot up the PinDMD logo was showing, but after launching a table and then exiting the display was blank. If I relaunched a table the DMD worked, but on exit again no logo whatsoever.

I checked I had the latest vpinmame DLL and flashed the firmware, but still no luck. I also set the new Pinmame registry entry 'ShowPinDMD' correctly. Then I thought I would try a non-UVP table and then it worked fine. I think I remember reading someone in this thread that it's because UVP doesn't call a function on exiting a table? Is there a way I can send the dmdlogo.txt file to the DMD directly (maybe with another program or using a DOS command? If that possible I can continue to use UVP and can simply change my FPLaunch to send the file when I exit the table (in fact I could randomly pick any one of several DMDs smile.gif).

Cheers

Vic

Edited by settingsons, 07 July 2012 - 07:51 PM.


#1322 russdx

russdx

    Pinball Fan

  • VIP
  • 1,317 posts
  • Location:Bristol UK

  • Flag: United Kingdom

  • Favorite Pinball: NBAFB

Posted 07 July 2012 - 08:20 PM

badboybill is going to be releasing an amazing dmd editor program that will be able to do all that correctly soon smile.gif

#1323 settingsons

settingsons

    Pinball Fan

  • VIP
  • 959 posts
  • Location:Switzerland

  • Flag: Switzerland

  • Favorite Pinball: Terminator 2 and many EM machines



Posted 07 July 2012 - 10:04 PM

It gets better and better smile.gif

#1324 Flying Dutchman

Flying Dutchman

    Pinball Wizard

  • VIP
  • 3,259 posts

  • Flag: ---------

  • Favorite Pinball: Medieval Madness / Champion Pub



Posted 14 July 2012 - 09:41 PM

Could anyone please confirm that below DMD is supported?

'Supported DMD?'

Cheers,
FD.

Edited by Flying Dutchman, 14 July 2012 - 09:42 PM.

'Flying Dutchman'

In need for a Backglass or 'Active Backglass / UVP' please 'click' on below and visit the complete revised website at:
Posted Image

#1325 russdx

russdx

    Pinball Fan

  • VIP
  • 1,317 posts
  • Location:Bristol UK

  • Flag: United Kingdom

  • Favorite Pinball: NBAFB

Posted 14 July 2012 - 10:23 PM

I use the 20002 not tried the 20002r but can't see any reason it wouldn't work I'm guessing it's got the same drive electronics

#1326 Flying Dutchman

Flying Dutchman

    Pinball Wizard

  • VIP
  • 3,259 posts

  • Flag: ---------

  • Favorite Pinball: Medieval Madness / Champion Pub



Posted 14 July 2012 - 10:33 PM

QUOTE (russdx @ Jul 14 2012, 11:23 PM) <{POST_SNAPBACK}>
I use the 20002 not tried the 20002r but can't see any reason it wouldn't work I'm guessing it's got the same drive electronics


Thanks!

Cheers,
FD.

'Flying Dutchman'

In need for a Backglass or 'Active Backglass / UVP' please 'click' on below and visit the complete revised website at:
Posted Image

#1327 JayP

JayP

    Enthusiast

  • Members
  • PipPipPip
  • 50 posts
  • Location:In the man cave located somewhere dark in South West London!

  • Flag: England

  • Favorite Pinball: ATFM, MM, TAF, CV, SS, TFTC...

Posted 08 August 2012 - 07:13 PM

Hi guys

I have been having an issue now with my DMD for around month or so and am now at my wits end.

I have upped a clip of my issue, apologies for the quality my old android is due a replacement!
PinDMD Issue

That skipping is not the phone it is the way it is. It started an obvious frame missing here and there to what you see as of todays clip.

For a bit of background this all started after I updated my PinDMD for the ghost fix. However after the weeks of trying to fix this it has only got worse and moving it to different machine stops the issue when I last checked a couple of days ago. That being said proves that the DMD, PinDMD, USB Cable and ribbon cable, PSU used only for DMD currently are fine.

So I thought it points either at the hardware of the cab machine or an issue with the OS or current install of the vp related software. Being I use WDS to deploy my cab it is no hassle for me to reinstall the OS multiple times. I have tried adding my golden build as it were and the problem was still there even though it was working for 2 months with that build with out a single glitch (OS and VP Ruled out). I have updated the drivers, I have taken completely fresh install of vp, vpinmame, the dll for PinDMD and even the Medieval B2S table which seems worst affected (Sadly the table it was built for in the first place!)

Worst of all the skipping happens in the VPinMameTest program nothing else running on the box. I used this for the clip.

The spec of the machine is the following:
Win7 Pro x64 (Not been a problem before, before anyone jumps at OS and it happens in XP so not that!)
Asus RoG Maximus V Gene
i7 2600K (Tried overclocked and STD)
2x Geforce 560ti (Bit over kill a whole card for backscreen!)
8GB of Ripjawz 2100
90gb Corsair Force GT SSD

I am now at a total loss, totally open to suggestions as over 10 years in IT is not helping me here. My weeks of testing has shown that it is not software, it's not the DMD hardware but always the same motherboard has the problem. However Asus aren't going to RMA board that is no longer able to run my DMD!

Jay whtflag.gif

#1328 deadsoulz

deadsoulz

    Enthusiast

  • Platinum Supporter
  • 175 posts

  • Flag: United States of America

  • Favorite Pinball: Creature from the Black Lagoon

Posted 08 August 2012 - 07:31 PM

Try Buying a cheap USB daughter board see if it may be your USB chipset.






#1329 ebarlow99

ebarlow99

    Ass Kicker

  • Members
  • PipPipPip
  • 349 posts
  • Location:MI

  • Flag: United States of America

  • Favorite Pinball: ALL

Posted 08 August 2012 - 07:35 PM

QUOTE (JayP @ Aug 8 2012, 03:13 PM) <{POST_SNAPBACK}>
Hi guys

I have been having an issue now with my DMD for around month or so and am now at my wits end.

I have upped a clip of my issue, apologies for the quality my old android is due a replacement!
PinDMD Issue

That skipping is not the phone it is the way it is. It started an obvious frame missing here and there to what you see as of todays clip.

For a bit of background this all started after I updated my PinDMD for the ghost fix. However after the weeks of trying to fix this it has only got worse and moving it to different machine stops the issue when I last checked a couple of days ago. That being said proves that the DMD, PinDMD, USB Cable and ribbon cable, PSU used only for DMD currently are fine.

So I thought it points either at the hardware of the cab machine or an issue with the OS or current install of the vp related software. Being I use WDS to deploy my cab it is no hassle for me to reinstall the OS multiple times. I have tried adding my golden build as it were and the problem was still there even though it was working for 2 months with that build with out a single glitch (OS and VP Ruled out). I have updated the drivers, I have taken completely fresh install of vp, vpinmame, the dll for PinDMD and even the Medieval B2S table which seems worst affected (Sadly the table it was built for in the first place!)

Worst of all the skipping happens in the VPinMameTest program nothing else running on the box. I used this for the clip.

The spec of the machine is the following:
Win7 Pro x64 (Not been a problem before, before anyone jumps at OS and it happens in XP so not that!)
Asus RoG Maximus V Gene
i7 2600K (Tried overclocked and STD)
2x Geforce 560ti (Bit over kill a whole card for backscreen!)
8GB of Ripjawz 2100
90gb Corsair Force GT SSD

I am now at a total loss, totally open to suggestions as over 10 years in IT is not helping me here. My weeks of testing has shown that it is not software, it's not the DMD hardware but always the same motherboard has the problem. However Asus aren't going to RMA board that is no longer able to run my DMD!

Jay whtflag.gif



i had the same thing happen...got the dmd it's own 5v power supply......never had a problem since...my pc is beefy too
just rmemeber to put a in-line fuse (on 5V line)between the psu and your dmd
http://www.ebay.com/...=item3a7395d884

a cheap fix if it solves it!

Edited by ebarlow99, 08 August 2012 - 07:37 PM.


#1330 russdx

russdx

    Pinball Fan

  • VIP
  • 1,317 posts
  • Location:Bristol UK

  • Flag: United Kingdom

  • Favorite Pinball: NBAFB

Posted 08 August 2012 - 07:36 PM

looks like the whole dmd is cutting out? is the psu on the new pc given enough current?

#1331 JayP

JayP

    Enthusiast

  • Members
  • PipPipPip
  • 50 posts
  • Location:In the man cave located somewhere dark in South West London!

  • Flag: England

  • Favorite Pinball: ATFM, MM, TAF, CV, SS, TFTC...

Posted 08 August 2012 - 07:39 PM

Thanks ebarlow99

Sorry should have said it is powered from a pc psu of it's own using a fuse in line also. Tried several PSU as well.

Jay

#1332 russdx

russdx

    Pinball Fan

  • VIP
  • 1,317 posts
  • Location:Bristol UK

  • Flag: United Kingdom

  • Favorite Pinball: NBAFB

Posted 08 August 2012 - 07:40 PM


pinkitty this might be a good idea for ur problem


QUOTE (deadsoulz @ Aug 8 2012, 08:31 PM) <{POST_SNAPBACK}>
Try Buying a cheap USB daughter board see if it may be your USB chipset.



#1333 JayP

JayP

    Enthusiast

  • Members
  • PipPipPip
  • 50 posts
  • Location:In the man cave located somewhere dark in South West London!

  • Flag: England

  • Favorite Pinball: ATFM, MM, TAF, CV, SS, TFTC...

Posted 08 August 2012 - 07:44 PM

Think I have a usb daughterboard somewhere good call! Thanks guys I will dig it out and report back!

I had previously tried a powered hub as well as it had been suggested.

Edited by JayP, 08 August 2012 - 07:46 PM.


#1334 russdx

russdx

    Pinball Fan

  • VIP
  • 1,317 posts
  • Location:Bristol UK

  • Flag: United Kingdom

  • Favorite Pinball: NBAFB

Posted 08 August 2012 - 07:47 PM

u using the same psu powering the board on the working/none working pc? the video really looks like a power problem

#1335 ebarlow99

ebarlow99

    Ass Kicker

  • Members
  • PipPipPip
  • 349 posts
  • Location:MI

  • Flag: United States of America

  • Favorite Pinball: ALL

Posted 08 August 2012 - 07:56 PM

that's what i thought.....

#1336 JayP

JayP

    Enthusiast

  • Members
  • PipPipPip
  • 50 posts
  • Location:In the man cave located somewhere dark in South West London!

  • Flag: England

  • Favorite Pinball: ATFM, MM, TAF, CV, SS, TFTC...

Posted 08 August 2012 - 07:57 PM

QUOTE (russdx @ Aug 8 2012, 08:47 PM) <{POST_SNAPBACK}>
u using the same psu powering the board on the working/none working pc? the video really looks like a power problem

Hi Russ

I have tried it powered from the PSU in the PC, several different PSUs externally on the cab hardware. I have tried it on another machine with all the external PSUs all were fine.

As I say lost! However can see where you are coming from as it does it when the DMD is about to flash if you catch my drift.


Thanks for the all prompt responses, this is a great community of pinball nutters!
Jay

#1337 russdx

russdx

    Pinball Fan

  • VIP
  • 1,317 posts
  • Location:Bristol UK

  • Flag: United Kingdom

  • Favorite Pinball: NBAFB

Posted 08 August 2012 - 07:58 PM

hmmm very strange. i hate problems tht make no sense lol

#1338 JayP

JayP

    Enthusiast

  • Members
  • PipPipPip
  • 50 posts
  • Location:In the man cave located somewhere dark in South West London!

  • Flag: England

  • Favorite Pinball: ATFM, MM, TAF, CV, SS, TFTC...

Posted 08 August 2012 - 08:04 PM

QUOTE (russdx @ Aug 8 2012, 08:58 PM) <{POST_SNAPBACK}>
hmmm very strange. i hate problems tht make no sense lol

I know what you mean!

Working in 3rd line support my life is full of problems, although usually other peoples! In this case I have to admit that I have battled alone for weeks and as result didn't even think of trying a USB addon card. Could have kicked myself when DeadSoulz suggested it.

Jay

#1339 PinKitty

PinKitty

    Enthusiast

  • Members
  • PipPipPip
  • 96 posts

  • Flag: United States of America

  • Favorite Pinball: High Roller Casino

Posted 08 August 2012 - 08:06 PM

Hey Jay,

Please let us know if the USB daughterboard works. I have had the same problem. I can get pinDMD to work on my small Compaq test computer running with XP, and also on my old cabinet pc running with Vista. BUT...

I can't get it to work on my beefy new cabinet computer, either. Although I know it talks to the pinDMD cuz I can update it's firmware on this computer. For some reason it doesn't get the signal through Visual Pinball on this computer. It just stays on the pinDMD.com logo.

I uninstalled VPinMAME and delete all VP and HyperPin files. Also uninstalled the pinDMD drivers. Then reinstalled everything from scratch. Didn't work. Then I took out the graphics card and ran a table on the integrated graphics. IT WORKED! It looked great! I was so happy! AND THEN...

About 20 seconds later, it started to glitch like yours. Then started double imaging, and then double imaged the double image - like looking into two mirrors. Then it scrambled and went out. Hooked it up to the old Vista cabinet computer, and it works great. Hooked it back to the new cabinet computer and all I get is the pinDMD.com logo screen.

Seems like something tricked the pinDMD board for a moment, but don't know what so it will work again.

#1340 JayP

JayP

    Enthusiast

  • Members
  • PipPipPip
  • 50 posts
  • Location:In the man cave located somewhere dark in South West London!

  • Flag: England

  • Favorite Pinball: ATFM, MM, TAF, CV, SS, TFTC...

Posted 08 August 2012 - 09:06 PM

QUOTE (PinKitty @ Aug 8 2012, 09:06 PM) <{POST_SNAPBACK}>
Hey Jay,

Please let us know if the USB daughterboard works. I have had the same problem. I can get pinDMD to work on my small Compaq test computer running with XP, and also on my old cabinet pc running with Vista. BUT...

I can't get it to work on my beefy new cabinet computer, either. Although I know it talks to the pinDMD cuz I can update it's firmware on this computer. For some reason it doesn't get the signal through Visual Pinball on this computer. It just stays on the pinDMD.com logo.

I uninstalled VPinMAME and delete all VP and HyperPin files. Also uninstalled the pinDMD drivers. Then reinstalled everything from scratch. Didn't work. Then I took out the graphics card and ran a table on the integrated graphics. IT WORKED! It looked great! I was so happy! AND THEN...

About 20 seconds later, it started to glitch like yours. Then started double imaging, and then double imaged the double image - like looking into two mirrors. Then it scrambled and went out. Hooked it up to the old Vista cabinet computer, and it works great. Hooked it back to the new cabinet computer and all I get is the pinDMD.com logo screen.

Seems like something tricked the pinDMD board for a moment, but don't know what so it will work again.


Hi PinKitty

Will update on the USB board, I think it might be at work. I will check tomorow and if I can't find it I'll grab another at the weekend.

I had something similar to this on a test box here it was an Asrock ION330HT (No laughing! Was the only free box at the time!), I thought being an Atom it would be that however I was wrong. There was a very short usb extension cable plugged in to make easier access to a rear USB port. I used this cable first time and got the same result you describe. Then tried without and it worked fine even with the atom running ATFM FS table on a single screen at 1080p (Shocked I was too when I discovered it played smooth as silk!)

Are you using an extension cable? Did you use the same USB cable when switching between machines?

Regards,
Jay