Jump to content



Photo
- - - - -

freescale


  • Please log in to reply
23 replies to this topic

#1 boiydiego

boiydiego

    Pinball Fan

  • Members
  • PipPipPipPip
  • 978 posts
  • Location:baal

  • Flag: Belgium

  • Favorite Pinball: flinstones,t2 chrome edition,wcs,afm,fish tales,medieval,rollercoaster tycoon,taxi

Posted 09 February 2015 - 05:41 PM

having problem with the freescale nudgeboard i have installed it its working but problem is when i hit my flippers to play the ball also move only from tapping the flipperbuttons what can i do about that ?


Edited by boiydiego, 09 February 2015 - 09:22 PM.

boiydiego___gebruik-n2kbkyc.png


#2 gtxjoe

gtxjoe

    VPF Veteran

  • VIP
  • 5,159 posts

  • Flag: United States of America

  • Favorite Pinball: Medieval Madness, AbraCadabra



Contributor

Posted 10 February 2015 - 01:28 AM

Deadzone setting is used allow you to fillter out small movements like that



#3 boiydiego

boiydiego

    Pinball Fan

  • Members
  • PipPipPipPip
  • 978 posts
  • Location:baal

  • Flag: Belgium

  • Favorite Pinball: flinstones,t2 chrome edition,wcs,afm,fish tales,medieval,rollercoaster tycoon,taxi

Posted 10 February 2015 - 10:41 AM

its not realy small movement more big movement , also changing the deadzone will affect the nudge making it react later to nudge ..


boiydiego___gebruik-n2kbkyc.png


#4 mjr

mjr

    Pinball Wizard

  • Members
  • PipPipPipPipPip
  • 3,346 posts

  • Flag: United States of America

  • Favorite Pinball: Medieval Madness

Posted 10 February 2015 - 08:16 PM

I sure don't know what would be causing that.  Is it something electrical or something mechanical, do you think?  I.e., does the unwanted nudging happen when the flipper switches make electrical contact, or does it happen purely from the vibration of tapping the buttons?  Is it *only* the flipper buttons that cause this or do you get the same extra nudging just tapping lightly on the side of the cabinet?  If it seems to be electrical, how are the flipper buttons wired?  What kind of key encoder are you using?

 

Did you do any calibration of the Freescale nudging with the Windows "Set up USB game controllers" control panel?  If so you should undo that by resetting everything to defaults in the control panel (Properties -> "Settings" tab ->  "Reset to default" button).  The software is self-calibrating and auto-centering - the Windows calibration works at cross purposes with that, so you should use the defaults.



#5 nicco84

nicco84

    Enthusiast

  • Members
  • PipPipPip
  • 150 posts

  • Flag: Italy

  • Favorite Pinball: medieval madness

Posted 12 February 2015 - 09:29 AM

Boyidiego I've you're same problem.
I installed Freescale in my cab just down right flipper button (Freescale was in plunger v2 kit bought here) and quite close to shaker (about 10 cm)
When I play if I hit left flipper or right flipper or activate shaker the ball became mad! It moves in every direction. Im sure is the vibration made by contractor and shaker. I could only decrease the value of x and y gain (about 300) and use shaker intensity at maximum 16 (for you could be different I don't know where is your shaker). It's really frustrating... It's like have have a Ferrari and never use it. If you use this method you will see you won't have this problem. But using those low values for x and y you have to nudge really strong with your body to move ball. Also tilt is a problem... If I put high value in tilt sensitivity (like 890) if I push quickly about ten time in right and left flipper table tilts (quickly without the danger and danger danger advise before). Same thing if activate shaker
I want to ask to Mjr if I flash Freescale with his method Is better... It's the only way for me because now my actual nudge system is not so good.

Edit: I've just seen in your link your Freescale software is incompatible with actual plunger v2 of virtuapin... So if I want to use your method I must modify also pluger

Edited by nicco84, 12 February 2015 - 09:56 AM.


#6 The Loafer

The Loafer

    Pinball Wizard

  • VIP
  • 3,472 posts
  • Location:Embrun, Ontario, Canada

  • Flag: ---------

  • Favorite Pinball: Superman, Firepower & Tron



Posted 12 February 2015 - 02:00 PM

U just need to increase the deadzone so that this type of vibration is not picked up, so what is your deadzone present setting? Remember also that this will require independant settings for vp9.9.0, physmod5 and vpx

#7 boiydiego

boiydiego

    Pinball Fan

  • Members
  • PipPipPipPip
  • 978 posts
  • Location:baal

  • Flag: Belgium

  • Favorite Pinball: flinstones,t2 chrome edition,wcs,afm,fish tales,medieval,rollercoaster tycoon,taxi

Posted 12 February 2015 - 02:49 PM

deadzone is now 42 procent also i use the modified versions from mjr ,thx for help in advance loafer


boiydiego___gebruik-n2kbkyc.png


#8 nicco84

nicco84

    Enthusiast

  • Members
  • PipPipPip
  • 150 posts

  • Flag: Italy

  • Favorite Pinball: medieval madness

Posted 12 February 2015 - 03:02 PM

I will try to edit the dead zone value.
I've virtuapin Freescale is in plunger v2, not Mjr method

#9 The Loafer

The Loafer

    Pinball Wizard

  • VIP
  • 3,472 posts
  • Location:Embrun, Ontario, Canada

  • Flag: ---------

  • Favorite Pinball: Superman, Firepower & Tron



Posted 12 February 2015 - 05:28 PM

I can't say a specific value because my cab is different from yours, my board is placed in different area, etc so you need to experiment with this value

Boiydiego: that is quite a high deadzone value. What the heck are your gain values and for what exe is that set up for?

#10 mjr

mjr

    Pinball Wizard

  • Members
  • PipPipPipPipPip
  • 3,346 posts

  • Flag: United States of America

  • Favorite Pinball: Medieval Madness

Posted 12 February 2015 - 06:51 PM

Okay, there's a bunch of different things going on in this thread - might be worth clarifying a few points.

 

1. "Freescale" is the hardware board included in the VirtuaPin v2 plunger kit.  It's also the hardware that runs the Pinscape project software.  But don't confuse them - they're completely different software even though they happen to run on the same hardware.  It's like Future Pinball and Visual Pinball - they both run on a PC, but you wouldn't try to give someone advice about how to set up FP by telling them about VP dialog settings.

 

If you have the VPv2 kit, *do not* install the Pinscape software.  It's not compatible with the VPv2 plunger hardware.

 

Boydiego, are you running the Pinscape software or the VPv2 kit?

 

2. If you're using the Pinscape software, it has its own dead zone management and auto centering.  You should *not* have to use a dead zone at all in VP or do any calibration in the Windows "set up USB game controllers" control panel.  If you set up calibration in the Windows control panel, you should delete it by clicking the "Reset to default" button in the control panel.

 

3. If you're using the Physmod5 version of VP (or some version other than 9.9), you will have to adjust the VP joystick gain settings in the "keyboard" options differently than in 9.9.  I haven't used pm5 a lot myself, but I think the gain settings there need to be much lower than the 9.9 settings.  In 9.9 the gain seems to work best at around 1000 with the Pinscape software, and I think in pm5 it's more like 10.



#11 nicco84

nicco84

    Enthusiast

  • Members
  • PipPipPip
  • 150 posts

  • Flag: Italy

  • Favorite Pinball: medieval madness

Posted 12 February 2015 - 07:48 PM

I wouldn't create problem but my problem is the same if boyidiego.

mjr I read about the incompatibility in your guide but thanks for explanation. My answer was if your method is better than v2 in order to prevent ball movement caused by vibration of contractors and shaker. In that case I will follow your method buying new Freescale and Plunger. Sorry if I bad explained my want

#12 mjr

mjr

    Pinball Wizard

  • Members
  • PipPipPipPipPip
  • 3,346 posts

  • Flag: United States of America

  • Favorite Pinball: Medieval Madness

Posted 12 February 2015 - 09:16 PM

mjr I read about the incompatibility in your guide but thanks for explanation. My answer was if your method is better than v2 in order to prevent ball movement caused by vibration of contractors and shaker. In that case I will follow your method buying new Freescale and Plunger. Sorry if I bad explained my want

 

I really don't know - I haven't seen these particular symptoms in my own set-up, so I don't know what's causing them.  So I don't know if changing your setup to the Pinscape software would help or not.  Here are some *potential* problems that would affect the VPv2 kit and Pinscape *equally*:  (1) your accelerometer gain is set too high in VP (fix by reducing VP gain settings), (2) you made calibration changes in the Windows control panel that are adding even more gain separately from VP or are setting the wrong center-point (fix by opening the Windows control panel and clicking the "Reset to default" button), (3) the Freescale board isn't securely mounted in the cab, so cabinet vibrations are getting mechanically amplified by the mounting (fix by making sure the Freescale board is screwed securely to the cabinet and can't move around within the cab or jiggle on its mounting screws).  

 

Also, boydiego reported his problem as being with the flipper buttons, so it's also possible there's something electrical going on.  But it wasn't clear to me if he was using the flipper buttons as an example of just how tiny a tap would set off the accelerometer, or if the electrical contact of the flipper buttons was actually required for the problem to manifest.  If your problem is that contactors are setting it off, that could also be electrical - does an equal amount of vibration from just tapping on the cabinet set it off, or does it only happen when the vibration is caused by a contactor or shaker motor?


Edited by mjr, 12 February 2015 - 09:18 PM.


#13 nicco84

nicco84

    Enthusiast

  • Members
  • PipPipPip
  • 150 posts

  • Flag: Italy

  • Favorite Pinball: medieval madness

Posted 12 February 2015 - 10:37 PM

1- already done
2- I will try with reset in control panel
3- board is locked in bottom of cab with 4 pcb feet... I tried also to put instead the four wood screw to put some soft glue (consistence of rubber) hoping to absorb some vibration but nothing to do.

I'm really sure is vibrating because if I activate the closest contactor to Freescale ball movements are more powerful than the last contactor simulate bumper (installed about under back box, so quite far from Freescale) yes also vibration of shaker give this problem and movements are continuous until shaker stop.

So my next steps are decrease x and y gain to acceptable values for real nudging with my body;
Increase dead zone
Reset virtuapin controller by control panel

Post shot to show Freescale position. On the right under right flipper button

2cnv2g3.jpg

Edited by nicco84, 12 February 2015 - 10:40 PM.


#14 The Loafer

The Loafer

    Pinball Wizard

  • VIP
  • 3,472 posts
  • Location:Embrun, Ontario, Canada

  • Flag: ---------

  • Favorite Pinball: Superman, Firepower & Tron



Posted 12 February 2015 - 11:33 PM

Sorry mjr's, didn't mean to lead them astray, misunderstood how Freescale worked.

#15 mjr

mjr

    Pinball Wizard

  • Members
  • PipPipPipPipPip
  • 3,346 posts

  • Flag: United States of America

  • Favorite Pinball: Medieval Madness

Posted 13 February 2015 - 12:49 AM

Nicco84 - the photo is kind of dark but it looks about right.  The Freescale is horizontal on the floor of the cab with screws through the screw holes in the board, right?  And I assume you have some spacers underneath, and that the board is screwed down.  Just to make sure, if you reach into the cab and try to jiggle the board manually, it feels securely attached to the cabinet and has no play at all, right?  

 

You really shouldn't have to have much dead zone at all.  To calibrate VP, I'd start by turning the dead zone off entirely (or down to zero), then turning the x and y gain down to the lowest level.  At this point you really should see no motion at all even with a pretty hard nudge to the cabinet.  If you're still seeing motion with small vibrations with those settings, there's something else wrong.  If it does in fact get rid of all motion, you can start adjusting the gain upwards to find the right gain level.  Again, do your adjustments with gain ONLY, keeping the dead zone at zero - it'll be too hard to separate the effects if you try to adjust both at the same time.  Once you have the gain at a realistic level, THEN you can adjust the dead zone as needed to get rid of spurious jitter when the cabinet isn't being nudged.

 
When adjusting settings in VP, remember that you have to close VP completely - player AND editor - and relaunch VP from Windows.  Changes won't go into effect until you quit completely out of VP and relaunch it.
 

If you can't get rid of the jitter by turning VP gain down to the lowest setting, the problem probably isn't in VP.  The place to start in that case is probably the Windows control panel - bring up the adjustment page and look at the little crosshairs diagram.  It will show you what the joystick interface from the Freescale board is reporting.  You should see the crosshairs jittering around a very small amount when everything is at rest, and more when you nudge the cabinet, proportional to how hard a nudge you give it.


Edited by mjr, 13 February 2015 - 12:52 AM.


#16 sliderpoint

sliderpoint

    Pinball Fan

  • Members
  • PipPipPipPip
  • 760 posts
  • Location:Spokane, WA

  • Flag: United States of America

  • Favorite Pinball: Metallica

Posted 13 February 2015 - 03:13 AM

Is that pic with everything powered on?  Why is there no light on the freescale board?  Are you sure you have the correct axis selected in VP for that device?

 

-Mike



#17 nicco84

nicco84

    Enthusiast

  • Members
  • PipPipPip
  • 150 posts

  • Flag: Italy

  • Favorite Pinball: medieval madness

Posted 13 February 2015 - 07:39 AM

Unluckily mjr for all you have asked answer is yes.
Horizontal fix in the cab, spacers are 4 pcb feet (about 4 cm height)... 4 screws in board to fix pcb feet and 4 wooden screws to fix board with feet in the bottom of cab. Try your method starting with 0 xy gain and deadzone. Arrived to 600 gain (for me right is about around 400) but no try deadzone. This evening I will try.
Always restart vp when change keys (no restart table but whole vp like suggested in your other thread).
I will try with reset in control panel but now crosshair movements in virtuapin proprieties are like you say... Very microscopic movements when I don't nudge and crosshair movements are right proportionally to the power of nudge.

Yes slider point shot has been done when I was reinstalling win8 and I was plugging in a device for time. In this shot Freescale wasn't connected but it works correctly with its led changing color when I move cab. I utilize this shot only to let see correct position of board. This evening Post a video so you will see better.

Really really thanks

#18 boiydiego

boiydiego

    Pinball Fan

  • Members
  • PipPipPipPip
  • 978 posts
  • Location:baal

  • Flag: Belgium

  • Favorite Pinball: flinstones,t2 chrome edition,wcs,afm,fish tales,medieval,rollercoaster tycoon,taxi

Posted 13 February 2015 - 08:59 AM

MJR its just the button that is causing this by tapping its in the zero slope so no contacter involved , iam gone get the leaf flipperbuttons like everybody use to see if this fixes problem ,its ,not electric problem because when i tough slow the button there is no problem i will send picture of button i use also the deadzone i needed to set to that to have little problem when touching the button , also use the freescaleboard and the pinscape software and your modified version of vp.990 and vpm5 also did not set the calibration in win 7 but to be sure i will remove/reset it before i had the sidewinder installed but dont remember if i used the win calibration for it ..


Edited by boiydiego, 13 February 2015 - 09:15 AM.

boiydiego___gebruik-n2kbkyc.png


#19 mjr

mjr

    Pinball Wizard

  • Members
  • PipPipPipPipPip
  • 3,346 posts

  • Flag: United States of America

  • Favorite Pinball: Medieval Madness

Posted 13 February 2015 - 06:20 PM

MJR its just the button that is causing this by tapping its in the zero slope so no contacter involved ,

 

Okay, no contactor is involved, but does the *button* have to be involved?  What I mean is: do you see the same excessive nudging if you just tap on the side of the cabinet *near* the button without actually touching the button?  I'm just trying to narrow down whether we should be looking for an explanation that's electrical or something purely mechanical.  I'm assuming it's mechanical, since it would be very strange indeed if electrical interference manifested this way, but since you've described the problem it in terms of tapping on the flipper buttons I just want to make sure.


I will try with reset in control panel but now crosshair movements in virtuapin proprieties are like you say... Very microscopic movements when I don't nudge and crosshair movements are right proportionally to the power of nudge.

 

That all sounds right, which would suggest that the hardware and the low-level joystick input are working correctly, which would definitely point to the VP settings as the prime suspect.


Edited by mjr, 13 February 2015 - 06:21 PM.


#20 nicco84

nicco84

    Enthusiast

  • Members
  • PipPipPip
  • 150 posts

  • Flag: Italy

  • Favorite Pinball: medieval madness

Posted 13 February 2015 - 06:34 PM

I try with 19 in deadzone and 950 x and y gain. Now I have no more problems with toys vibration... Nudge with body is quite real.... Thanks for hel mjr... Otherwise nudge is not perfect how I expect and tilt doesn't work correctly.

I will order a Freescale and will try pinscape ;)
thanks