Jump to content



Photo
- - - - -

LEDWIZ wiring


  • Please log in to reply
9 replies to this topic

#1 kore64

kore64

    Hobbyist

  • Platinum Supporter
  • 10 posts
  • Location:Wisconsin

  • Flag: United States of America

  • Favorite Pinball: AFM, MM, MBOPB, MB, TOTAN

  • PS3 Gamer Tag: kore-64

Posted 18 May 2015 - 03:57 PM

Just looking for a little verification. I am pretty weak in EE. I do have the LEDs working, but just picked up some solenoids. I wanted to make sure before I tried this setup fried something.

 

Would I be better off isolating the 12v circuit with some relays instead? Or will this work?

 

9qJ8e1M.png

 

 



#2 zebulon

zebulon

    Cantankerous old B****D

  • Platinum Supporter
  • 1,179 posts
  • Location:Whitby, Ontario, Canada

  • Flag: Canada

  • Favorite Pinball: xenon, Medieval Madness, Royal Flush, Silverball Mania

Posted 18 May 2015 - 05:42 PM

That solenoid is likely to overload the output on the ledwiz.  You'll want to make sure that the draw is less than 500ma.


 ZB%20%20Storefront1%20.png               [email protected]

Don't pm or expect an answer from me here ... the links above are my contacts.

I know so much about so little that I could teach you all there is to know about nothing......


#3 kore64

kore64

    Hobbyist

  • Platinum Supporter
  • 10 posts
  • Location:Wisconsin

  • Flag: United States of America

  • Favorite Pinball: AFM, MM, MBOPB, MB, TOTAN

  • PS3 Gamer Tag: kore-64

Posted 18 May 2015 - 06:01 PM

Ah ok thanks.Relays it is then. Pretty sure these draw around 2amps each.

 

I was assuming the 500ma restriction was only if I was using the USB supplied power.

 

Thanks again for the reply!



#4 Outhere

Outhere

    Pinball Wizard

  • Platinum Supporter
  • 4,807 posts

  • Flag: United States of America

  • Favorite Pinball: M M

Posted 18 May 2015 - 06:16 PM

I don't believe there's any reason to run positive voltage to the LEDWiz board

http://www.vpforums....31471&hl=ledwiz

Here is the web site that sells the Ledwiz  (Installation Docs) that may help

http://groovygamegea...products_id=239


Edited by Outhere, 18 May 2015 - 09:44 PM.


#5 Pinfritz

Pinfritz

    Neophyte

  • Members
  • Pip
  • 9 posts

  • Flag: Austria

  • Favorite Pinball: Taxi

Posted 22 September 2026 - 07:55 AM

 

I'm a bit confused. I bought some "RGB Ultimarc Gold Leaf buttons," but I can't find much information regarding the series resistors that are apparently needed when using an LED-Wiz. Does anyone here have experience with this combination? Can anybody help?


Edited by Pinfritz, 22 September 2026 - 07:55 AM.


#6 mjr

mjr

    Pinball Wizard

  • Members
  • PipPipPipPipPip
  • 3,346 posts

  • Flag: United States of America

  • Favorite Pinball: Medieval Madness

Posted 22 September 2026 - 09:08 PM

My guess is that those buttons have the necessary resistors built-in. Anything that's a finished product like that usually does.  If you can't find any information about it on the product page, it's a good sign that nothing else is needed, but you could email the vendor to ask them if you want to be sure. 

 

Do you have a multimeter?  If so, you could try applying power and measuring the current, BRIEFLY, to see if it's within the expected range.  I'd say anything under about 50 mA confirms that resistors are present.  If the resistors AREN'T there, the measured current will be much higher, which will eventually overheat the LED, but you can probably get away with it for a few seconds without doing any damage.  I think the odds are so good that these have built-in resistors that you wouldn't be taking much risk.



#7 Pinfritz

Pinfritz

    Neophyte

  • Members
  • Pip
  • 9 posts

  • Flag: Austria

  • Favorite Pinball: Taxi

Posted 23 September 2026 - 07:12 AM

My guess is that those buttons have the necessary resistors built-in. Anything that's a finished product like that usually does.  If you can't find any information about it on the product page, it's a good sign that nothing else is needed, but you could email the vendor to ask them if you want to be sure. 

 

Do you have a multimeter?  If so, you could try applying power and measuring the current, BRIEFLY, to see if it's within the expected range.  I'd say anything under about 50 mA confirms that resistors are present.  If the resistors AREN'T there, the measured current will be much higher, which will eventually overheat the LED, but you can probably get away with it for a few seconds without doing any damage.  I think the odds are so good that these have built-in resistors that you wouldn't be taking much risk.

 

From the Ultimarc site https://www.ultimarc...ushbuttons-rgb/  :

"IMPORTANT: The LEDs do not have current-limiting resistors so must be connected to one of the above controllers which have current-controlled outputs."



#8 mjr

mjr

    Pinball Wizard

  • Members
  • PipPipPipPipPip
  • 3,346 posts

  • Flag: United States of America

  • Favorite Pinball: Medieval Madness

Posted 23 September 2026 - 06:31 PM

From the Ultimarc site https://www.ultimarc...ushbuttons-rgb/  :

"IMPORTANT: The LEDs do not have current-limiting resistors so must be connected to one of the above controllers which have current-controlled outputs."

 

In that case you'll have to get the specs from them on the LED voltage and current.  Once you have that, search online for "LED Resistor Calculator" for tools to calculate the resistor size.  You just need to plug in the "forward voltage" and "forward current" specs for the LEDs, and the voltage of your power supply.



#9 Pinfritz

Pinfritz

    Neophyte

  • Members
  • Pip
  • 9 posts

  • Flag: Austria

  • Favorite Pinball: Taxi

Posted 28 September 2026 - 05:33 AM

so, thats the answer of ultimarc himself:

 

"Its difficult to give an accurate value. You could try using 150 ohms. But each channel may need a different value. If the white is not balanced you may need to change one or more."

 

Arnoz Boards have the resistors going with 320/320 and 374 Ohms - the last one for red

so i can take it to proof it by try and measurement and calculate or take a value in the middle of all...



#10 mjr

mjr

    Pinball Wizard

  • Members
  • PipPipPipPipPip
  • 3,346 posts

  • Flag: United States of America

  • Favorite Pinball: Medieval Madness

Posted 28 September 2026 - 05:39 PM

so, thats the answer of ultimarc himself:

"Its difficult to give an accurate value. You could try using 150 ohms. But each channel may need a different value. If the white is not balanced you may need to change one or more."

 

It's not actually that difficult - there's a well-defined way to get the correct numbers.  They need to give you two numbers so you can calculate the resistors - the terms to ask for are "Forward Voltage Drop" and "Forward Current".  Those are standard specifications for every LED, and the manufacturer should know them.  Each color channel will have slightly different values; the forward current will likely be between 20mA and 50A per channel, and will probably be the same for all three channels.  The forward voltage drops will typically be about 2V for the Red channel and about 3V for the Blue and Green channels.  If you can pry those numbers out of the vendor, plug them into an LED resistor calculator, along with your power supply voltage, and you'll get the correct resistor values.


Edited by mjr, 28 September 2026 - 05:39 PM.