Jump to content



Photo
* * * * * 2 votes

usb dot matrix driver board - who wants one?


  • Please log in to reply
1473 replies to this topic

#1401 thewool

thewool

    Pinball Fan

  • VIP
  • 1,068 posts
  • Location:North Yorkshire, UK

  • Flag: England

  • Favorite Pinball: WOZ



Posted 28 September 2012 - 08:04 PM

Ok Russ, thought that would be the case :)

Just wondered if there was an alternative such as displaying a portion of the 192x64 displaying.

Edited by thewool, 28 September 2012 - 08:04 PM.


#1402 russdx

russdx

    Pinball Fan

  • VIP
  • 1,317 posts
  • Location:Bristol UK

  • Flag: United Kingdom

  • Favorite Pinball: NBAFB

Posted 29 September 2012 - 10:24 AM

i think the current version does this horizontally and it resizes it vertically :)

#1403 The Loafer

The Loafer

    Pinball Wizard

  • VIP
  • 3,472 posts
  • Location:Embrun, Ontario, Canada

  • Flag: ---------

  • Favorite Pinball: Superman, Firepower & Tron



Posted 16 October 2012 - 07:21 PM

Hi Russ/All,

At 71 pages, this is starting to be a bit tough to search through lol. On the issue of .ShowPinDMD, was there ever a solution to disable it for when using UVP?

Loaf

#1404 russdx

russdx

    Pinball Fan

  • VIP
  • 1,317 posts
  • Location:Bristol UK

  • Flag: United Kingdom

  • Favorite Pinball: NBAFB

Posted 16 October 2012 - 08:55 PM

Hey :)

No :( we dont have access to tht code :(

#1405 The Loafer

The Loafer

    Pinball Wizard

  • VIP
  • 3,472 posts
  • Location:Embrun, Ontario, Canada

  • Flag: ---------

  • Favorite Pinball: Superman, Firepower & Tron



Posted 17 October 2012 - 12:35 AM

I am surprised some access can't be provided through your vpinmame.dll, but I ain't no coder so... :)

Question: can you shut off access to your board outside of vpinmame? I figure that most people who use your board are probably users of Hyperpin. Users of HP are familiar with fplaunch which is used to launch the tables and fplaunch is quite configurable. So my idea? Is it possible to shut off and turn on your board outside of vp/VPm, then maybe fplaunch can, when launching a UVP table, first turn off the board, load the UVP table and then when exiting, can turn it back on again?

#1406 bent98

bent98

    Pinball Fan

  • Members
  • PipPipPipPip
  • 1,077 posts
  • Location:NY

  • Flag: United States of America

  • Favorite Pinball: Roadshow, Haunted House, Safe Cracker

Posted 17 October 2012 - 12:47 AM

There was a solution for uvp bg that don't require dmd to be enabled. Like Xenon for example. You disable the pindmd via the registry in the specific game rom section.

Edited by bent98, 17 October 2012 - 12:49 AM.


#1407 The Loafer

The Loafer

    Pinball Wizard

  • VIP
  • 3,472 posts
  • Location:Embrun, Ontario, Canada

  • Flag: ---------

  • Favorite Pinball: Superman, Firepower & Tron



Posted 17 October 2012 - 02:46 AM

ohhh that's great. I don't recall such a post, is there a specific registry key to edit?

#1408 russdx

russdx

    Pinball Fan

  • VIP
  • 1,317 posts
  • Location:Bristol UK

  • Flag: United Kingdom

  • Favorite Pinball: NBAFB

Posted 17 October 2012 - 08:49 AM

yes the board can be controlled outside of pinmame.dll :)

badboybills DMD software has full control over it :) (just send a blank frame to clear the current frame (ie turn off))

http://www.hyperspin...yperDMD-Support


me and snotz need access to the UVP server to tell it what the new pinDMD flags are without telling it (in code) it wont know what they are and this is where the problem is, without access to the source to add the new option there is nothing we can do :(

#1409 Aurich

Aurich

    Enthusiast

  • Members
  • PipPipPip
  • 306 posts
  • Location:Southern California

  • Flag: ---------

  • Favorite Pinball: Scared Stiff

Posted 17 October 2012 - 04:26 PM

russdx have you been following the B2S server stuff? Looks like it's getting close to ready for prime time (working great on first test table, Sorcerer) and with it being under active development maybe it would be a a good place to get that option added, I'm sure the developer is open to ideas like that that would benefit everyone.

Edit: Here's the post about the B2S server if you missed it - http://www.vpforums....=60#entry196143

Edited by Aurich, 17 October 2012 - 04:29 PM.


#1410 russdx

russdx

    Pinball Fan

  • VIP
  • 1,317 posts
  • Location:Bristol UK

  • Flag: United Kingdom

  • Favorite Pinball: NBAFB

Posted 17 October 2012 - 04:41 PM

not following at all, but will mention this to snotz, hopefully we can get the flag added :)

#1411 Zablon

Zablon

    Pinball Fan

  • Members
  • PipPipPipPip
  • 642 posts

  • Flag: United States of America

  • Favorite Pinball: Funhouse

Posted 17 October 2012 - 11:46 PM

Russ - just a followup on my earlier DMD cutting out issue. I flashed back to older firmware and older DLL and had same flickering issue but while toggling the jumper I noticed the screen was flickering. It would seem there was a loose connection where the fuse holder is. Once I tightened that up, all flickering went away and I updated everything back up to the newest versions and no issues. BTW the no ghosting is great! :D

#1412 bent98

bent98

    Pinball Fan

  • Members
  • PipPipPipPip
  • 1,077 posts
  • Location:NY

  • Flag: United States of America

  • Favorite Pinball: Roadshow, Haunted House, Safe Cracker

Posted 18 October 2012 - 01:04 AM

ohhh that's great. I don't recall such a post, is there a specific registry key to edit?


Here you go loafer

New dll uploaded. Once you run a game, it will add showpindmd to the key for the game you just ran.

For those not familiar, the registry settings are located at:

HKEY_CURRENT_USER
Software
Freeware
Visual PinMame
[gamename]

Once in the gamename key, you will see the showpindmd value on the right side (if you ran that game with this new dll)
Value of 1 shows the pinDMD. 0 turns it off and keeps the dmdlogo.txt shown.

We did not remove the com control, so the scripting (controller.ShowPinDMD = ) still works for the tables that dont use UVP.

#1413 The Loafer

The Loafer

    Pinball Wizard

  • VIP
  • 3,472 posts
  • Location:Embrun, Ontario, Canada

  • Flag: ---------

  • Favorite Pinball: Superman, Firepower & Tron



Posted 18 October 2012 - 02:46 AM


ohhh that's great. I don't recall such a post, is there a specific registry key to edit?


Here you go loafer

New dll uploaded. Once you run a game, it will add showpindmd to the key for the game you just ran.

For those not familiar, the registry settings are located at:

HKEY_CURRENT_USER
Software
Freeware
Visual PinMame
[gamename]

Once in the gamename key, you will see the showpindmd value on the right side (if you ran that game with this new dll)
Value of 1 shows the pinDMD. 0 turns it off and keeps the dmdlogo.txt shown.

We did not remove the com control, so the scripting (controller.ShowPinDMD = ) still works for the tables that dont use UVP.


This is outstanding, thanks very much!

#1414 russdx

russdx

    Pinball Fan

  • VIP
  • 1,317 posts
  • Location:Bristol UK

  • Flag: United Kingdom

  • Favorite Pinball: NBAFB

Posted 18 October 2012 - 08:40 AM

Thats great Zablon, JayP also messaged me saying his flickering issue was a lose power cable as well hehe, looks like these displays are very sensitive.

Glad its all working ok :)

#1415 Aurich

Aurich

    Enthusiast

  • Members
  • PipPipPip
  • 306 posts
  • Location:Southern California

  • Flag: ---------

  • Favorite Pinball: Scared Stiff

Posted 06 November 2012 - 07:46 PM

Got my pinDMD up and running with a real display finally, after months of the board sitting there lonely, waiting for a DMD.

Russ is a saint, if you have a cabinet you should get a real DMD, it's such an upgrade over emulating one on a monitor. :)

#1416 russdx

russdx

    Pinball Fan

  • VIP
  • 1,317 posts
  • Location:Bristol UK

  • Flag: United Kingdom

  • Favorite Pinball: NBAFB

Posted 06 November 2012 - 11:36 PM

nothing beats real hardware :)

#1417 penguins

penguins

    Hobbyist

  • Members
  • PipPip
  • 32 posts

  • Flag: Canada

  • Favorite Pinball: Shrek

Posted 22 November 2012 - 01:19 AM

Wow, looks like someone finally got PinDMD to work with Future Pinball tables.

http://www.youtube.c...bed/29n6kKcvwgs

Russ, expect more orders :) ... when is your next batch of boards available?

Edited by penguins, 22 November 2012 - 02:06 AM.


#1418 vulbas

vulbas

    Enthusiast

  • Members
  • PipPipPip
  • 216 posts
  • Location:villebon sur yvette (essonne)

  • Flag: France

  • Favorite Pinball: medieval madness

Posted 06 December 2012 - 09:28 PM

hello,
I received my dmd of pinled. this is perfect.
Dimslightly flickering pixels on some animations. I'll do the manipulation given in the pdf.
 
20121206142130-vulbas-20121206-134542.jpg
 
more image :

 

Attached Files



#1419 russdx

russdx

    Pinball Fan

  • VIP
  • 1,317 posts
  • Location:Bristol UK

  • Flag: United Kingdom

  • Favorite Pinball: NBAFB

Posted 06 December 2012 - 10:38 PM

glad u like it :)

 

the slightly flickering dim pixels was one of the minor problems on the pinDMD1

 

this is completely solved in pinDMD2 :)



#1420 vulbas

vulbas

    Enthusiast

  • Members
  • PipPipPip
  • 216 posts
  • Location:villebon sur yvette (essonne)

  • Flag: France

  • Favorite Pinball: medieval madness

Posted 08 December 2012 - 07:28 AM

I would like one pindmd2. but I just bought the pindmd1 :(