Jump to content



Photo
* * * * * 2 votes

pinDMD-2 development :)


  • Please log in to reply
838 replies to this topic

#461 bosvrucht

bosvrucht

    Enthusiast

  • Members
  • PipPipPip
  • 410 posts

  • Flag: Netherlands

  • Favorite Pinball: LOTR

Posted 29 January 2013 - 02:50 PM

hey Hotdp, could you give us some pointers/guide on how you adjusted the segments on your Pinled? Mine is good enough as is, but as you showed, you can get it near 100% invisible gridlines. Did you just pull them off, and then put them back again? or did you nudge them in to place?

 

thanks!



#462 hotdp

hotdp

    Enthusiast

  • Members
  • PipPipPip
  • 434 posts

  • Flag: Denmark

  • Favorite Pinball: T2

Posted 29 January 2013 - 03:00 PM

hey Hotdp, could you give us some pointers/guide on how you adjusted the segments on your Pinled? Mine is good enough as is, but as you showed, you can get it near 100% invisible gridlines. Did you just pull them off, and then put them back again? or did you nudge them in to place?

 

thanks!

 

Hi,

Sure!

First of all I did not do anything before I contacted PinLED (Would not damage anything) and this is what they wrote back (great support btw):

 

 

please use a small screwdriver to annul carefully one segment after another. Make sure that you don't bent the legs of the segments. Make sure that you align the segments the right way when you put them back in.
Start with the two far right segments...

 

I toke a screwdriver under each led-segment put pressure where it was to low. I startet with one side and then went to the other side. After that they where all levelled (If you look from all sides).

One place (to the right) there was still to much space between the segments, so I started putting pressure on those elements. Thats it!

 

I hope it makes sense what I am trying to say :-) If not please let me know and I will try again hehe.



#463 bosvrucht

bosvrucht

    Enthusiast

  • Members
  • PipPipPip
  • 410 posts

  • Flag: Netherlands

  • Favorite Pinball: LOTR

Posted 29 January 2013 - 03:44 PM

@hotdp

 

So you did not follow Pinleds (awkwardly worded) advice on removing the segments and re-placing them? You just forced them straight, while still socketed?



#464 hotdp

hotdp

    Enthusiast

  • Members
  • PipPipPip
  • 434 posts

  • Flag: Denmark

  • Favorite Pinball: T2

Posted 29 January 2013 - 04:21 PM

@hotdp

 

So you did not follow Pinleds (awkwardly worded) advice on removing the segments and re-placing them? You just forced them straight, while still socketed?

 

Correct, I did not remove the segments I just moved them up/down so they where all level. 

After that I forced the ones who had to much space with the hands.

Try take a picture of the segments from the side, I would like to see how yours are.



#465 Westworld

Westworld

    Enthusiast

  • Members
  • PipPipPip
  • 114 posts
  • Location:Munich

  • Flag: Germany

  • Favorite Pinball: Kiss

Posted 02 February 2013 - 12:10 PM

Anybody here with a pinDMD-2 using HyperDMD?

 

I tried to use HyperDMD 1.0.4 (on Win764bit) to move the display for JPSalas Spiderman to the DMD, which works quite fine on screen (DMD emulation), but the 'real' DMD stays dark.

The documentation says it would simply work after enabling PinDMD.

 

I wonder if it was ever tested with PinDMD-2, maybe it works only with the first version, or if it is an issue with Win7 64 bit - or something totally different?

 

Anybody tried it successfully so far?



#466 russdx

russdx

    Pinball Fan

  • VIP
  • 1,317 posts
  • Location:Bristol UK

  • Flag: United Kingdom

  • Favorite Pinball: NBAFB

Posted 02 February 2013 - 02:33 PM

pinDMD2 is not supported yet.



#467 ArcadiusMaximus

ArcadiusMaximus

    Quit throwing trash into my dimension !

  • Members
  • PipPipPip
  • 310 posts
  • Location:PITZBORG, PA

  • Flag: United States of America

  • Favorite Pinball: Attack from Mars, Scared Stiff, White Water

Posted 02 February 2013 - 08:00 PM

Just got my screen in yesterday and fired it up for the first time this morning ! Well worth the 5 month wait ! I have a question though and sorry if its been answered already but can you disable pinDMD on certain tables that have the score on an active backglass such as Back to the Future?


~ Mr. John E. Smith III Esq.

#468 russdx

russdx

    Pinball Fan

  • VIP
  • 1,317 posts
  • Location:Bristol UK

  • Flag: United Kingdom

  • Favorite Pinball: NBAFB

Posted 02 February 2013 - 08:38 PM

there is code to support some alphanumeric tables, but i dont think it works correctly when used with the animated back glasses.



#469 Westworld

Westworld

    Enthusiast

  • Members
  • PipPipPip
  • 114 posts
  • Location:Munich

  • Flag: Germany

  • Favorite Pinball: Kiss

Posted 03 February 2013 - 09:53 AM

 can you disable pinDMD on certain tables that have the score on an active backglass such as Back to the Future?

 

Usually you need to open the table script, look for .hidden=0 or controller.hidden=0 or .hidden=false and replace that with =1, such as .hidden=1

 

If you had a 3 screen cabinet you normally already did that before, there is no difference if it is a 3rd screen emulating the DMD or a real DMD. You can reach for pinDMD the same by opening the registry, selecting the rom name and look for ShowPinDMD and set that to 0. 



#470 Zablon

Zablon

    Pinball Fan

  • Members
  • PipPipPipPip
  • 642 posts

  • Flag: United States of America

  • Favorite Pinball: Funhouse

Posted 03 February 2013 - 11:29 AM

In addition - for B2S  tables that you don't want the DMD to run (due to scores being on backglass) you need to add:

.ShowPinDMD = 0    (or false)

 

to the table script.

 

For UVP screens you do what Westworld posted.



#471 russdx

russdx

    Pinball Fan

  • VIP
  • 1,317 posts
  • Location:Bristol UK

  • Flag: United Kingdom

  • Favorite Pinball: NBAFB

Posted 03 February 2013 - 02:18 PM

finished the custom settings firmware :) need to test it a bit more / get a few people to test to make sure its stable.

 

you will be able to set the intensity to what you want and the pinDMD2 will remember it. you can also set the refresh rate but this shouldn't really be needed.

 

settingsn.png

 

You will need to download the a new version of the firmware (ill release once tested properly) and then another little pinDMDsettings.exe(as seen above) I made it using an older .net framework so it should work fine on xp/vista/win7 (iv tested it on loads of pcs and it seams to work great)

 

once the new firmware is installed. run the pinDMDsettings.exe and it will read your current firmware settings. then you can change them to how you want the DMD to look. then press save to apply the settings to the pinDMD. you can just load the pinDMDsettings.exe at any time and swap the settings :) the pinDMD stores the new settings in flash so it will remember them even when it loses power.



#472 vulbas

vulbas

    Enthusiast

  • Members
  • PipPipPip
  • 216 posts
  • Location:villebon sur yvette (essonne)

  • Flag: France

  • Favorite Pinball: medieval madness

Posted 03 February 2013 - 02:36 PM

very good job !!

thx



#473 russdx

russdx

    Pinball Fan

  • VIP
  • 1,317 posts
  • Location:Bristol UK

  • Flag: United Kingdom

  • Favorite Pinball: NBAFB

Posted 03 February 2013 - 03:06 PM

it seams to be working ok :)

 

 

if any one wants to have a quick play before i release details below :)

 

new firmware here

application here

 

upgrade the firmware how you normally would.

 

once the pc detects the pinDMD2 after firmware upgrade. run the pinDMDsettings.exe and swap the settings about, you should see the effect in real time on the pinDMD firmware logo. once your happy with the settings press 'save' and it will save them. you should be able to unplug and plug back in the pinDMD2 and it will remember them.

 

 

let me know if you have any issues with any of it :)



#474 ArcadiusMaximus

ArcadiusMaximus

    Quit throwing trash into my dimension !

  • Members
  • PipPipPip
  • 310 posts
  • Location:PITZBORG, PA

  • Flag: United States of America

  • Favorite Pinball: Attack from Mars, Scared Stiff, White Water

Posted 04 February 2013 - 04:15 PM

In addition - for B2S  tables that you don't want the DMD to run (due to scores being on backglass) you need to add:

.ShowPinDMD = 0    (or false)

 

to the table script.

 

For UVP screens you do what Westworld posted.

 

Thanks to both of you. I will try this out today :D


~ Mr. John E. Smith III Esq.

#475 Arcade4

Arcade4

    Pinball Fan

  • Members
  • PipPipPipPip
  • 1,686 posts
  • Location:Beaumont, TX.

  • Flag: United States of America

  • Favorite Pinball: AC/DC

Posted 05 February 2013 - 04:44 PM

Russ, I was just reading the Pinball Arcade thread about their cabinet version they want to do some day soon. Any chance you have contacted them to see if their program could talk to your PinDmd board?
I'm probably just dreaming, but that would be really cool.

Edited by Arcade4, 05 February 2013 - 04:45 PM.


#476 hotdp

hotdp

    Enthusiast

  • Members
  • PipPipPip
  • 434 posts

  • Flag: Denmark

  • Favorite Pinball: T2

Posted 05 February 2013 - 05:50 PM

"some day soon". Do you have a link?



#477 ArcadiusMaximus

ArcadiusMaximus

    Quit throwing trash into my dimension !

  • Members
  • PipPipPip
  • 310 posts
  • Location:PITZBORG, PA

  • Flag: United States of America

  • Favorite Pinball: Attack from Mars, Scared Stiff, White Water

Posted 05 February 2013 - 07:24 PM

In addition - for B2S  tables that you don't want the DMD to run (due to scores being on backglass) you need to add:

.ShowPinDMD = 0    (or false)

 

to the table script.

 

For UVP screens you do what Westworld posted.

 

Thanks to both of you. I will try this out today :D

I had not luck adding .ShowPinDMD = 0 in the script. I actually had to edit the registry for each table I wanted to disable pinDMD for. Thanks again guys.


Edited by ArcadiusMaximus, 05 February 2013 - 07:24 PM.

~ Mr. John E. Smith III Esq.

#478 Aurich

Aurich

    Enthusiast

  • Members
  • PipPipPip
  • 306 posts
  • Location:Southern California

  • Flag: ---------

  • Favorite Pinball: Scared Stiff

Posted 06 February 2013 - 06:22 AM

Russ, I was just reading the Pinball Arcade thread about their cabinet version they want to do some day soon. Any chance you have contacted them to see if their program could talk to your PinDmd board?
I'm probably just dreaming, but that would be really cool.

I'm holding my breath for that to even see the light of day, let alone work wiht a real DMD, but that would be very cool if it happened.

#479 Pinball999

Pinball999

    Pinball Fan

  • Members
  • PipPipPipPip
  • 828 posts
  • Location:Germany

  • Flag: France

  • Favorite Pinball: Star Wars

Posted 06 February 2013 - 07:46 AM

Russ, I was just reading the Pinball Arcade thread about their cabinet version they want to do some day soon. Any chance you have contacted them to see if their program could talk to your PinDmd board?
I'm probably just dreaming, but that would be really cool.

I'm holding my breath for that to even see the light of day, let alone work wiht a real DMD, but that would be very cool if it happened.

Was also expecting this since the release date of the first tables pack for PS3.

But then got a bit frustrated.. the game has way too many issues (delays, strange ball behaviour) to be fully enjoyable. And I'm not even talking about the pink filter they add to their tables..



#480 jasonsmith

jasonsmith

    Enthusiast

  • Members
  • PipPipPip
  • 214 posts
  • Location:BC, Canada

  • Flag: Canada

  • Favorite Pinball: AFM

Posted 13 February 2013 - 07:47 AM

So I had an issue today where installing WinIpac totally messed with my system causing an 0xc0000005 exception error when I tried to start FP or VP. I uninstalled that, got everything working again except I can't get any info to the DMD. 

 

I see the pinDMD.com logo, no issue there but when playing a table VP or FP it just stays on the .com logo. It all worked without issue an hour before. I pulled the pinDMD USB out and put it back in hopefully to fix it, no luck, I have rebooted and even shut down many times, no luck, I reinstalled the drivers also with no luck. 

 

I sure wish it worked again, no idea what is going on right now. 

 

Win7 64bit, with firmware 557-16

 

 

EDIT: FIXED - Completely removed the device and driver and re-installed it all, that did the trick. Darn WinIpac, have no idea what the heck it did but it wasn't funny. 


Edited by jasonsmith, 13 February 2013 - 07:58 AM.