Yeah, still have my original one... But going through a divorce right now so my mind is alittle foggy
Got it to work... Ruzz, the link to the DMD in the install area or download area is wrong....
Ruzz Sent you an email please check =)
Posted 19 January 2013 - 11:20 AM
hey Hacker, checked all the links im aware of and they are all correct? which link did you click that was wrong hehe?
Current: NBA Fastbreak, Hook, Stranger Things (Pro)
Gone: Bram Stoker's Dracula, Revenge From Mars, Lethal Weapon 3, Medieval Madness (Remake), Mary Shelley's Frankenstein, Earthshaker, Big Buck Hunter Pro
pinDMD3 Now Available!
Videos of pinDMD in action | www.pinDMD.com
Posted 19 January 2013 - 06:19 PM
(Step2) Run setDFU.exe. Your computer shoulddetect a new USB device.
Where do I find that .exe?
I have "DfuSeDemo.exe" but not that one?
EDIT:
Found it:
http://www.pindmd.co...ds-v2/firmware/
Maybe you should add that to the manual? I was looking in the installed folder.
Edited by hotdp, 19 January 2013 - 06:22 PM.
Posted 19 January 2013 - 07:49 PM
some thing is very wrong there! its not even trying.
the DMD is not receiving any data from the pinDMD2
make sure the ribbon cable connectors are firmly plugged in.
take the DMD off the anti static bubble wrap.
does the pc detect the pinDMD2? when you plug it in
what voltage are you running the pinLED at?
Current: NBA Fastbreak, Hook, Stranger Things (Pro)
Gone: Bram Stoker's Dracula, Revenge From Mars, Lethal Weapon 3, Medieval Madness (Remake), Mary Shelley's Frankenstein, Earthshaker, Big Buck Hunter Pro
pinDMD3 Now Available!
Videos of pinDMD in action | www.pinDMD.com
Posted 19 January 2013 - 07:52 PM
ohh no :-( I am always so unlucky!

Posted 19 January 2013 - 07:53 PM
does the pinDMD2 show up as a usb device on your pc?
Current: NBA Fastbreak, Hook, Stranger Things (Pro)
Gone: Bram Stoker's Dracula, Revenge From Mars, Lethal Weapon 3, Medieval Madness (Remake), Mary Shelley's Frankenstein, Earthshaker, Big Buck Hunter Pro
pinDMD3 Now Available!
Videos of pinDMD in action | www.pinDMD.com
Posted 19 January 2013 - 07:57 PM
ok for some reason either the pinDMD2 is just not outputting any dmd data or the pinLED is not working. I have only ever seen a xpin have a fault like this.
or the ribbon cable is dodgy (seriously doubt this!)
do you have a volt meter by any chance?
Current: NBA Fastbreak, Hook, Stranger Things (Pro)
Gone: Bram Stoker's Dracula, Revenge From Mars, Lethal Weapon 3, Medieval Madness (Remake), Mary Shelley's Frankenstein, Earthshaker, Big Buck Hunter Pro
pinDMD3 Now Available!
Videos of pinDMD in action | www.pinDMD.com
Posted 19 January 2013 - 08:13 PM
ok out of my 100 batch 4 boards has a fault which is the exact same fault you have here, it was some excess solder on the DMD header shorting some of the DMD io pins to ground. (i thought i had mended them all) maybe this is the same fault
unplug the board and turn it on its back. and then put it so the header is vertical to you so the DMD header pins are vertical
put your meter into continuity mode.
start at the bottom of the header put one probe on the left pin and the other probe on the right pin, this should be an OPEN circuit. the meter should not beep or say closed circuit. do this for all 7 rows going up.
like
7 7
6 6
5 5
4 4
3 3
2 2
1 1 probe between 1 and 1, then 2 and 2
make sure the pinDMD is unplugged from the DMD and pc
if all 7 pairs of pins are open circuit. it looks like the pinDMD2 is ok (or some thing else has gone wrong) Quickest way is for me test it my self, as your in denmark and im uk the shipping will be fast and i can confirm if the board is good or bad
and have the same/replacement back to you pretty fast ![]()
EDIT
i don't suppose you own an oscilloscope lol? (you can test the board 100% if you have hehe)
Edited by russdx, 19 January 2013 - 08:16 PM.
Current: NBA Fastbreak, Hook, Stranger Things (Pro)
Gone: Bram Stoker's Dracula, Revenge From Mars, Lethal Weapon 3, Medieval Madness (Remake), Mary Shelley's Frankenstein, Earthshaker, Big Buck Hunter Pro
pinDMD3 Now Available!
Videos of pinDMD in action | www.pinDMD.com
Posted 19 January 2013 - 08:36 PM
I have two beep/connections i have marked them with yellow on the image.

i don't suppose you own an oscilloscope lol? (you can test the board 100% if you have hehe)
no ![]()
Wait I might misunderstand.
I but the meter on -> (the number rises if there is a connection)
I then check every leg for connection right?
If I switch my red/black pointer I get a different result? (more circuts)
Edited by hotdp, 19 January 2013 - 08:42 PM.
Posted 19 January 2013 - 08:51 PM
ok this is GOOD
can u turn the board over and on the set of pins closest to the chip (so in that photo the ones on the left) can you take a high res picture of the back and can you check to see for excess solder on the pin. and see if you can clear it. scrape it off or use a soldering iron to wipe it off.
it sounds to me like excess solder is shorting these 2 pins to ground. (not sure how it past test, maybe knocked around in post pushed the solder or somin)
this is the same fault i had on 4 boards. i thought they where dead but with further testing it was just some pins shorting to ground from excess solder from assembly. once i cleared the solder the boards worked great. (i still have those 4 boards so yours is not one of them)
once the excess solder is removed you should have an open connection between these to pairs of pins. and then fingers crossed it will come alive and be fine ![]()
on the meter the ohms should hit 0 (beeep) if there is a connection, an open circuit the omhs should be a high number as in no resistance.
any of the pairs that beeped will be shorted (most likely excess solder)
Edited by russdx, 19 January 2013 - 08:45 PM.
Current: NBA Fastbreak, Hook, Stranger Things (Pro)
Gone: Bram Stoker's Dracula, Revenge From Mars, Lethal Weapon 3, Medieval Madness (Remake), Mary Shelley's Frankenstein, Earthshaker, Big Buck Hunter Pro
pinDMD3 Now Available!
Videos of pinDMD in action | www.pinDMD.com
Posted 19 January 2013 - 08:57 PM
hmm might be doing the test wrong, the pins look clean to me only like 1 or 2 would be shorted if there was a problem. if you have a really good close look do they all look ok?
actually third pin down on the left, looks like some crap at the top of the pin? can you clear this?
might be easiest if you return the board and i can test it?
Edited by russdx, 19 January 2013 - 08:59 PM.
Current: NBA Fastbreak, Hook, Stranger Things (Pro)
Gone: Bram Stoker's Dracula, Revenge From Mars, Lethal Weapon 3, Medieval Madness (Remake), Mary Shelley's Frankenstein, Earthshaker, Big Buck Hunter Pro
pinDMD3 Now Available!
Videos of pinDMD in action | www.pinDMD.com
Posted 19 January 2013 - 09:08 PM
when you test each pair of pins are they all open circuit or are some still beeping on the meter?
Current: NBA Fastbreak, Hook, Stranger Things (Pro)
Gone: Bram Stoker's Dracula, Revenge From Mars, Lethal Weapon 3, Medieval Madness (Remake), Mary Shelley's Frankenstein, Earthshaker, Big Buck Hunter Pro
pinDMD3 Now Available!
Videos of pinDMD in action | www.pinDMD.com